Ariens 921020 Manual do Utilizador descarregar pdf

Page 1 of 5

Date: January 15, 2010 No. C-2007

Ariens Company has learned that under certain conditions the attachment belts used on the Sno-Thro

model 921020 in the serial number range listed above may intermittently grab the engine sheave when the

clutch is released. This grabbing will cause the auger and impeller to engage briefly. The affected units

were placed under a stop sales order per Product Notice N-2019 released on December 30, 2009.

Replacing the attachment drive belts p/n 07200521 originally used on these units with p/n 07200536 HA

raw edge belts eliminates the potential for the belts to grab.

Before putting any of the above-listed units into service, inspect the unit. If the unit has belt p/n 07200521

(the part number will be printed on the belt), order and install HA raw edge belt set p/n 07200536. Each set

contains two belts; order one set per unit. Discard the p/n 07200521 belts removed from the units. After the

belts have been replaced, the units can be removed from the stop sales list and retailed to customers. The

belt replacement procedure starts on page 2.

NOTE: 921020 models that are shipped from Ariens Company on or after January 15, 2010 already have

the p/n 07200536 HA raw edge belts installed and will not need to be reworked.

Dealers should file a warranty claim for each belt replacement, using flat rate code 21-999. Note each

unit’s model and serial number. Belt replacement will be reimbursed for 0.50 hours at the dealer’s standard

shop labor rate.

Please direct any questions about the inspection or warranty reimbursement policies to Ariens Technical

Service, 888-927-4367.

Ariens Company

655 W. Ryan St.

Brillion, WI 54110-1072

www.ariens.com

Service Campaign

Product Family: 921020 Sno-Thro 30LE Deluxe

Subject: Attachment Belt Engagement

Dealer Action: Replace Attachment Belts Before Sale

Model Serial Number Ranges Description

921020 000101 – 001229 30LE Deluxe

1 2 3 4 5

Resumo do Conteúdo

Página 1 - Service Campaign

Page 1 of 5Date: January 15, 2010 No. C-2007Ariens Company has learned that under certain conditions the attachment belts used on the Sno-Thro mod

Página 2 - 5. Cap Screws

Page 2 of 5Date: January 15, 2010 No. C-2007ATTACHMENT DRIVE BELT REPLACEMENTNOTE: The instructions presented below assume a unit has been set up

Página 3

Page 3 of 5Date: January 15, 2010 No. C-2007Install New Attachment Drive Belts1. Place new p/n 07200536 attachment belts onto attachment pulley.NO

Página 4

Page 4 of 5Date: January 15, 2010 No. C-2007Check Attachment Clutch Adjustment1. Loosen jam nut on cable adjustment barrel, and then turn the adju

Página 5

Page 5 of 5Date: January 15, 2010 No. C-20073. Loosen idler adjustment nut, and move idler closer to the attachment belts to increase spring exten

Mais documentos para Sopradores de neve Ariens 921020

Para ver o documento Ariens 921020 Manual do Utilizador

Ariens 921020 Manual do Utilizador (2 páginas)

Comentários a estes Manuais

Sem comentários

Ariens 921020 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Sopradores de neve Ariens 921020. C-2007 - Ariens Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Sopradores de neve Ariens 921020

Comentários a estes Manuais

Manuais e produtos relacionados com Sopradores de neve Ariens 921020