Ariens 915057 - 2148 Manual de Serviço

915 ZOOM EZT & IZT00459900 7/05Printed in USAService ManualModels 915055, 057, 059, 065, 067, 501, 502

4 - 94.2 MOVING UNIT MANUALLYDisengage (2) transmission bypass levers to drive unit and engage (1) transmission bypass levers to push unit manually (

4 - 104.5 AXLE LOCKS (915067, 055, 057, 059, 501) (Figure 5)NOTE: The unit comes shipped with the front axle in the lockout position.If a pivoting fr

4 - 114.7 LEVELING AND ADJUSTING PITCH OF MOWER DECKAdjust on a level surface, with the tires inflated to the correct air pressure.Level Mower Deck1.

4 - 12See Figure 9 for anti-scalp locations on models 915067, 055, 057, 059, 501. See Figure 10 for anti-scalp locations on model 915065 and 502.There

4 - 13To adjust the neutral setting for no wheel rotation Model IZT 915055, 057, 059, 067, 501:1. Use a hex wrench to loosen the locking bolt (Figure

4 - 14• Move levers to neutral position. • Loosen mounting hardware. • Position steering levers. • Tighten mounting hardware. 3. Adjust height of stee

5 - 155.1 ENGINE TROUBLESHOOTINGThe following troubleshooting chart is to be used to isolate engine problems and give possible causes and corrective

5 - 165.2 CHECKING ENGINE OILCheck the engine oil daily prior to use.IMPORTANT: Never operate the engine with the oil below the low mark on the dipst

5 - 177. Remove fuel line from engine first. Drain fuel from line back into fuel tank.8. Remove the electric clutch and the anti-rotation bolt.9. Remo

5 - 18Figure 16123345PE07602.3.1.Rear of Unit5.915055, 057, 059 915065, 067 5.915501, 502915501, 502915501, 5023.4.1. Oil Drain Tube2. Oil Drain Valve

1Section 1 - Introduction . . . . . . . . . . . . . . . . . . 1-21.1 The Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21.2 S

6 - 196.1 REPLACING PTO BELTRemove (Figure 17)1. Lower mower deck to the ground.2. Remove belt covers from mower deck.3. Hook a puller into idler hol

6 - 20Do not change angle of cutting edge or round the corner at the end of mower blade.2. Sharpen mower blade by removing an equal amount of material

7 - 217.1 HYDRO TRANSMISSION TROUBLESHOOTINGThe following troubleshooting chart is to be used to isolate hydro transmission problems and give possibl

7 - 22Figure 20Figure 217.2 HYDRO-GEAR FLUID RECOMMENDATIONSThe fluids used in Hydro-Gear transaxles have been carefully selected, and only equivalen

7 - 237.4 REPLACING HYDROSTATIC BELTRemove (Figure 22)Figure 221. Remove PTO belt (see Replacing PTO Belt).2. Disconnect electric clutch connector.3.

8 - 248.1 LIFT SYSTEMRefer to Figure 25 for the lift system.The mower pan lift system is a manual lift system controlled by the operator.Mower Lift P

9 - 259.1 STEERING CONTROLSSerial numbers 10,000 and above:Refer to Figure 26 thru Figure 27 for Steering.The steering controls should remain in the

9 - 26Figure 27Serial numbers below 10,000:Refer to Figure 28 and Figure 30 for Steering.The steering controls will swing outward when in neutral. In

9 - 27Figure 281. Transaxle Link2. Rod Pivot3. Steering Switch4. Dampener5. Handlebar6. Roll Pin124563312Model EZT 915065 and 502 with Serial Numbers

9 - 28Figure 29PE01721. Rod Transaxle2. Switch3. Jam Nuts4. Nyloc Jam Nut5. Handlebar6. Dampener7. Roll PinModel IZT 915055, 057, 059, 067, 501 with S

1 - 21.1 THE MANUALThe purpose of this manual is to provide complete instructions for service, maintenance, disassembly, repair, and installation of

9 - 299.2 ADJUSTING STEERING LEVER HEIGHT FOR SERIAL NUMBERS ABOVE 10,000 ONLY(Figure 30)Figure 30NOTE: Perform steps 1 and 2 for both steering lev

10 - 3010.1 FUEL SYSTEM TROUBLESHOOTINGThe following troubleshooting chart is to be used to isolate fuel system problems and give possible causes are

10 - 3110.2 FUEL PUMPThe impulse style fuel pump is the most commonly used fuel pump. Impulse fuel pumps may either be mounted externally onto the ca

11 - 3211.1 TOOLSThere are some specialized tools and test equipment that are needed for electrical repair work. A brief description of these follows

11 - 33Voltage MeasurementThere are two basic rules to be remembered when using a voltmeter. A voltmeter measures the voltage difference between the t

11 - 34IMPORTANT: ALWAYS follow information provided on battery and battery charger. Contact battery and battery charger manufacturers for detailed in

11 - 3511.5 SOLENOID AND RELAYSSolenoid and relays are both magnetically operated devices. Both devices operate on the principle that passing a curre

11 - 36current to a direct current is called a RECTIFIER. A diode is one type of rectifier.To check a diode, isolate if from the circuit by disconnect

11 - 37For models with serial numbers above 10,000 when the ignition switch is in the run position and with the steering switch in the neutral (engage

11 - 382 sets of contacts, one normally open, one normally closed. Contact resistance is 0.1-0.3 ohms when correct.Normally open contacts manually act

2 - 32.1 SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Ale

11 - 39Normally open contacts (big terminals) coil resistance 3.0-5.0 ohms. Contact resistance is 0.1-0.3 ohms when correct. Electrically activated.Co

11 - 4011.11 ELECTRICAL SYSTEMFigure 33 To EngineTo Engine1. Relay2. Clutch Switch3. Hour Meter4. Key Switch5. Switch NO6. Switch, Double Pole NO/NO

11 - 4111.12 WIRING DIAGRAMSModel 915055, 057, 059, 065, 067, 501, 502 for Serial Numbers Above 10,000

11 - 4211.13 CONTINUITY DIAGRAM

11 - 4311.14 ELECTRICAL FOR SERIAL NUMBERS ABOVE 5,000 AND BELOW 9,999Safety Interlock SystemWARNING: Safety Interlock failure and improper operation

11 - 44Diode check out: Diodes are checked with an ohm meter set on the diode check, and should only pass voltage in one direction. If it passes volta

11 - 45Pins 85-86 coil resistance 87-100 ohms. pins 30-87 normally open. Pins 30-87A normally closed. Contact resistance is 0.1-0.3 ohms when correct.

11 - 4611.15 ELECTRICAL SYSTEMFigure 341. Relay2. Clutch Switch3. Key Switch4. Switch NO5. Neutral Switch6. Interlock Switch235416Model 915055, 057,

11 - 4711.16 WIRING DIAGRAMSModel 915055, 057, 059, 065, 067, 501, 502 for Serial Numbers Between 5,000 and 9,999

11 - 4811.17 CONTINUITY DIAGRAM

2 - 4• Understand location and function of all controls.• Never allow operation by untrained persons.• Disengage PTO, stop unit and engine, set parkin

11 - 4911.18 ELECTRICAL FOR SERIAL NUMBERS BELOW 5,000Safety Interlock SystemWARNING: Safety Interlock failure and improper operation of unit can res

11 - 50.Contact resistance is 0.1-0.3 ohms when correct.Normally open contacts manually activated. contact resistance is 0.1-0.3 ohms when correct.2 s

11 - 51Pins 85-86 coil resistance 87-100 ohms. pins 30-87 normally open. Pins 30-87A normally closed. Contact resistance is 0.1-0.3 ohms when correct.

11 - 5211.19 ELECTRICAL SYSTEMFigure 35Model 915055, 057, 059, 065, 067, 501, 502 for Serial Numbers Below 5,0001. Relay2. Clutch Switch3. Key Switch

11 - 5311.20 WIRING DIAGRAMSModel 915055, 057, 059, 065, 067, 501, 502 for Serial Numbers Below 5,000

11 - 5411.21 CONTINUITY DIAGRAM

12 - 5512.1 MOWER SPINDLE REMOVALFigure 36The spindles are assemblies that are replaced when worn. To remove the spindle assemblies:1. With the mower

12 - 56TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTIONEngine will not crank/start1. Safety interlock system is not engaged or is faulty.2. Fuel tanks

12 - 57Unit moves with engine off and parking brake engaged1. The parking brake needs adjustment.2. Faulty parking brake.1. Contact your Ariens Dealer

12 - 58SERVICE PARTSBE SURE TO ALWAYS USE GENUINE ARIENS PARTS TO KEEP YOUR UNIT RUNNING LIKE NEWPART NO. QTY DESCRIPTION03498400 1 40-inch Mower Blad

2 - 5DO NOT try to stabilize the machine by putting your foot on the ground.Know the weight of loads. Limit loads to those you can safely control and

Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com

2 - 6of charger to positive (+) terminal, and negative (-) lead to negative (-) terminal.ALWAYS disconnect negative (-) cable FIRST and positive (+) c

3 - 7SECTION 3 - SPECIFICATIONSModel Number 915065 915502 915067 915055 915501 915057 915059Model 1540 1540 1740 1944 1844 2148 2352EngineTypeSingle C

4 - 84.1 CONTROLS AND FEATURESFigure 2SECTION 4 - GENERAL MAINTENANCE & ADJUSTMENTS1. Ignition Switch2. PTO Switch3. Throttle Lever4. Seat5. Stee